- 您现在的位置：买卖IC网 > Sheet目录1200 > C8051F320DK-U (Silicon Laboratories Inc)DEV KIT FOR C8051F320/F321
C8051F32x
4.1. System Clock Sources
The C8051F320 device installed on the target board features a calibrated programmable internal oscillator which is
enabled as the system clock source on reset. After reset, the internal oscillator operates at a frequency of 1.5 MHz
(±1.5%) by default but may be configured by software to operate at other frequencies. Therefore, in many
applications an external oscillator is not required. However, if you wish to operate the C8051F320 device at a
frequency not available with the internal oscillator, an external crystal may be used. Refer to the C8051F32x data
sheet for more information on configuring the system clock source.
The target board is designed to facilitate the installation of an external crystal. Remove shorting blocks at headers
J9 and J10 and install the crystal at the pads marked Y1. Install a 10 M ? resistor at R9 and install capacitors at
C14 and C15 using values appropriate for the crystal you select. Refer to the C8051F32x data sheet for more
information on the use of external oscillators.
4.2. Switches and LEDs
Three switches are provided on the target board. Switch SW1 is connected to the RESET pin of the C8051F320.
Pressing SW1 puts the device into its hardware-reset state. Switch SW2 and SW3 are connected to the
C8051F320’s general purpose I/O (GPIO) pins through headers. Pressing SW2 or SW3 generates a logic low
signal on the port pin. Remove the shorting blocks from the header to disconnect SW2 and SW3 from the port pins.
The port pin signals are also routed to pins on the J1 I/O connector. See Table 1 for the port pins and headers
corresponding to each switch.
Three LEDs are also provided on the target board. The red LED labeled PWR is used to indicate a power
connection to the target board. The green LEDs labeled with port pin names are connected to the C8051F320’s
GPIO pins through headers. Remove the shorting blocks from the header to disconnect the LEDs from the port pin.
The port pin signals are also routed to pins on the J1 I/O connector. See Table 1 for the port pins and headers
corresponding to each LED.
Also included on the C8051F320 target board is a 10 K ? Thumb-Wheel Rotary Potentiometer, part number R14.
The Potentiometer is connected to the C8051F320’s GPIO pin through a header. Remove the shorting block from
the header to disconnect the Potentiometer from the port pin. The port pin signal is also routed to a pin on the J1 I/
O connector. See Table 1 for the port pin and header corresponding to the Potentiometer.
Table 1. Target Board I/O Descriptions
Description
SW1
SW2
SW3
Green LED
Green LED
Red LED
Potentiometer
I/O
Reset
P2.0
P2.1
P2.2
P2.3
PWR
R14
Rev. 0.9
Header
none
J3[1–2]
J3[3–4]
J3[5–6]
J3[7–8]
none
J13
7
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
C850-260-WHX
CIRCUIT PROT 260MA 850VIMP TBU
CAN0005WP
VARISTOR 18VDC 4A 0402
CB4-B0-24-650-121-C
CIRCUIT BREAKER 50A 4POLE 8 PIN
CBBJ159
TRS BULKHEAD RCPT STR PCB
CBBJ379
TRT BULKHEAD JACK STR PCB THREAD
CBBJ79
TRB BULKHEAD JACK STR PCB 3-LUG
CBBJR26
BNC BULKHEAD JACK INSUL R/A PCB
CBBJR29
BNC BULKHEAD JACK R/A PCB
相关代理商/技术参数
C8051F320-GQ
功能描述:8位微控制器 -MCU 16KB 10ADC USB 32P MCU Rev E RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F320-GQR
功能描述:8位微控制器 -MCU 16KB 10ADC USB 32Pin Tape and Reel RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F320R
功能描述:8位微控制器 -MCU 10 ADC 32 Pin RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F320-TB
功能描述:插座和适配器 With C8051F320 MCU RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x
C8051F320-TB-K
功能描述:BOARD PROTOTYPING W/C8051F320 制造商:silicon labs 系列:- 零件状态:在售 板类型:评估平台 类型:MCU 8-位 核心处理器:8051 操作系统:- 平台:- 配套使用产品/相关产品:C8051F32x 安装类型:固定 内容:板 标准包装:1
C8051F321
功能描述:8位微控制器 -MCU 16KB 10ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F321-GM
功能描述:8位微控制器 -MCU 16KB 10ADC USB 28P MCU REV E RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F321-GMR
功能描述:8位微控制器 -MCU 16KB 10ADC USB 28P MCU REV E RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT